Indospark Construction Services

Chemical Capsule ccs

 
Chemical capsule ccs
 
Primarily used where anchor consistency is required and injection resin use would be prohibitive or inconvenient . Due to the viscous nature chemical capsuleCCSis not suitable for overhead installations or perforated and hollow substrates.

  • Description
  • Product Range
  • Installation
  • Loadchart
Description :

The chemical capsule CCS is a high performance rapid cure spin-in chemical anchor system based on optimum measured proportions of high strength epoxy acrylate resin, chemical activator and quartz aggregate sealed in a glass capsule. It is a fast install, simple to use system requiring no special tools and provides high strength stress free anchoring in concrete and solid masonry. The system operates by spinning a chisel ended anchor stud using the required drive adaptor through the capsule using a rotary hammer drill which crushes and mixes the contents in the drill hole and intiates the curing process, the stud is left in position to fully cure and from a high strength bond which is stronger than the base material. Capsule sizes are drill hole specific from M8 to M30 diameters. The system can be used with longer than standard threaded bars combined with multiple down hole capsules, studs should be cut chisel ended and separate drive adapters are available for connection to a drilling machine.

Advantages :

Rapid cure.
Consistent load behavior.
Suitable for static and dynamic loading.
Fast and simple to install.
Imparts no expansion stresses on the base material.
Usable in wet drill holes ( requires longer cure time).
Drill hole cleanliness not as critical as injection systems.
High-performance resin guarantees high loads in the base material.
The resin anchoring is free of expansion forces and permits low axial spacings and edge distances.
Flush finish, no projecting bolt after dismanting the fixture.
Installation - concrete and solid masonry

 Drill hole to correct diameter and depth, diamond cored drill holes should be roughened prior to installation.
 Clean drill hole thoroughly using wire brush / blow and remove all dust using a out pump or airline.
 Place the capsule in the drill hole ensuring fitting is below the surface.
 Attach the driver to the anchor stud, fit the drill and drive through the capsule until the stud reaches the base of the hole or the depth marker on the stud is reached.
 Detach the drive tool and leave stud undisturbed until cured and then attach fixture and torque to required setting.
 Insert clean fixing with a rotating motion until resin can be seen at the mouth of the hole, remove any excess immediately.
 Leave undisturbed until cured and then attach fixture and torque to required setting.

Installation


Dispenser DM 300

Steel body and mechanism

Description :

 
The professional dispenser DM300 for use with chemical mortar cartridges CM300PESF & CM300EASF.

 
Dispenser DM300 Variant 300ml 10:1 ratio cartridge

  Material steel body and mechanism



Dispenser DM 380


 
Steel body and mechanism

 


 
Description :

 
The professional dispenser DM380 for use with chemical mortar cartridges CM380EASF & CM380VESF.

 
Dispenser DM380 Variant 380ml co-axial 10:1 ratio cartridge

  Material steel body and mechanism



Dispenser DM 400

 
Steel body and mechanism

 


 
Description  
The professional dispenser DM400 for use with chemical mortar cartidge CM400PE.

Dispenser DM400 Variant 400ml side by side 1:1 ratio cartidge

  Material steel body and mechanism

Mixer nozzle MN

 
plastic  


Description :

 
Spare mixer nozzles for use with chemical mortar cartridges CM 300PESF, CM300EASF, CM380EASF, CM380VESF & CM400PE.

Mixer nozzle MN Variant co-axial

  Material plastic



Accessories for drill hole cleaning

 
Blow-out pump BP

 
plastic

 


Description :

 
The hand operated blow out pump BP is for drill hole cleaning prior to anchor installation.

 
Mixer nozzle MN Variant hand operated

  Material ABS



Cleaning brush CB

 
plastic

 


Description :

 
Wire brush CB is for thorough cleaning and hole preparation.

Cleaning brush CB Variant hand operated

  Material steel body and head

 
 
Contact Us
INDO-SPARK CONSTRUCTION
SERVICES
Pune Address :
Chandralok Housing Society, " Mangal Murti ", 686 / C / 2, Near Bata Show Room and Chandralok Hospital Lane, Bibvewadi, Pune - 37, Maharashtra, India.
Tel. No. : +91 - 20 - 24224537

Mobile : +91 - 98231 96066
              +91 - 98233 44299

 
Head Office Address :
198 E, Tararani Chowk, Near Geeta
Mandir,  Kolhapur - 416 003 ,
Maharashtra, India
Tel. No. : +91 - 231 -  2663581
Telefax : +91 - 231 -  6681005
Mobile : +91 - 98231 92194
Email :
Visit Also :
www.indospark.com
 
 
Contact to Mr. Sandeep Ingale-DIR.
Please visit at:
www.indospark.in/id/sandeepingale